- #How to connect n1mm logger to elecraft kx3 serial#
- #How to connect n1mm logger to elecraft kx3 software#
If you use the USB / Serial adapter from Elecraft, it is probably an FTDI device.
Eight Band Equalizer Starting Points Freq > 0.05 0.1 0.2 0.4 0.8 1.6 2.4 3.2 HC-4/5 -10 -4 -2 0 0 +2 +4 +4 Wide -12 -10 -6 -2 0 +6 +8 +10 The above settings are for "normal" operation.ĬOM Port Information: The K3 rear panel RS232 port is connected to my computer COM Port 1 via a 9 pin serial cable. Remember to set the Mic Gain and Mic Bias properly, as described above.
The table that follows details starting points for operation using two main categories of mics: the "articulated" elements (HC-4 and HC-5 based mics), and the "wide range" elements, typified by the iCM, Handi Mic iC, and PR 781 and the PR 20/30/40 genre. Be sure to listen to yourself on a separate receiver (with its antenna disconnected and noise blanker turned off) as you make final adjustments to optimize the settings for your operating situation. The best setup for your voice, your microphone, and your operating objectives may differ. DSP Settings and Mic Connections: Elecraft K3 Note: These are starting points only. Heil published the following information in their website article, “DSP Settings and Mic Connections: Elecraft K3. The "VOX Gain" is set with the "MENU" system. The "CMP/PWR/MON" knob will be used to set the Compression value.
The "Speed / MIC / Delay" knob will set to "MIC" (green light will display) is used to set the Mic Gain. Here are the settings I am currently using: The MIC Selection was set on the previous page using the "MENU" system. Set Set “SPKRS” “SPKR+PH” 2 Yes Settings depend on one's voice and how you want to sound. If not using the AD-1 (Kenwood/Elecraft Red Adapter Cable), the Heil Pro-Set Plus! headset 1/8" gray mono plug connects to the K3 rear panel "MIC MONO" connector. If using the Heil AD-1 (Kenwood/Elecraft Red Adapter Cable) the headset 1/8” gray mono plug connects into the AD-1, which is connected to the K3 front panel “MIC” connector. Headset & Microphone Information: One can connect the Heil Pro-Set Plus! to the K3 front panel to the K3 rear panel. PTT In Cable to Foot switch (using plug adapter) Key Out Cable to TEN-TEC amplifier PTT/VOX controller Some would argue this should be titled “PTT Out” REF In Capped – not used C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes. Key Currently not in use on my K3 This is a three-circuit jack, but the ring is not used thus if you wish to this connection, use a two conductor plug. Paddle Cable to CW Paddle This is a three-circuit jack so a three circuit plug is necessary. Transceiver Rear Panel Connections: Antenna 1 Coax cable from TEN-TEC Titan Amplifier “RF Input” Antenna 2 Currently not in use AUX RF Currently not in use 12 VDC In Power cable from power supply 12 VDC Out Currently not in use Ground # 6 Copper wire to radio room ground RS232 Port RS232 (Serial) cable from K3 to computer serial port 1 ACC Port Currently not in use SPKRS Currently not in use PHONES Heil Pro-Set Plus! black headphone stereo plug MIC MONO Heil Pro-Set Plus! gray micropho
#How to connect n1mm logger to elecraft kx3 software#
Modifications & Updates: Extreme Signal Protection IF Output Buffer KSYN3 Filter Terminator Added C101 on front panel Replaced AF/RF gain knobs Current Software C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes. Software CW Decoder DX4WIN LP-Bridge MMTTY N1MM WinPSK 19 19 16 19 19 19 Split Operation 61 Spurious Signal Removal SSB Operation SSTV 49 28 47 SUB Receiver 52 Ten-Tec Titan Amplifier 51 Transceiver Setup 7 USB / Serial Adapters 18 VOX Delay 72 C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes. Index 6 Meters 54 AGC Discussion Settings 31 36 ALC Connection 114 APF 68 ATU 29 Breakout Box 74 Carrying Case 37 COM Port Information 15 Configuration CW Operation Config Menu Entries CWT 5 21 88 41 Digital Mode Operation CW PSK RTTY PSK, AFSK & FSK Programming 14 25 23 26 Factory Reset 55 Filter Setup 56 C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes.įrequency Calibration 53 Front Panel Controls 65 Function Keys 79 Headset Information 10 JT65 Mode 111 LP_Bridge Software 16 Macro Use Mailing List MCU Boot Loader 74 40 109 Menu Settings 84 MIC Adjustment Data CW or SSB 10 17 18 Modifications & Updates 6 Noise Reduction Notch 45 50 P3 Power “Gain” Calibration 21 Preamp 71 PSK 25 QSK 64 Remote Control Roofing Filter RTTY 80 61 23 C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes. Elecraft K3 Operational Notes Serial: 2462 Compiled by Tony McClenny, N3ME C:\My Documents\Ham\Equipment\Elecraft\Elecraft K3 General Notes.
0 kommentar(er)
